Installing Ubuntu 7.04 Server via debootstrap
From Soekris Info Wiki
These instructions describe how I installed Ubuntu 7.04 on my 256MB Soekris net4801 by using debootstrap to build a CF card on a host system running Ubuntu 7.10. I installed 7.04 server on the net4801, but these steps should work for desktop or for 7.10 or you can also easily adapt them to install to a 2.5″ or SATA drive.
There are docs on the Ubuntu Wiki available on how to install Ubuntu on a Soekris via PXE but I did not feel like going through the hassle of setting PXE up to boot one system one time. I did borrow a few steps from the Ubuntu document.
I assume that you have a working knowledge of Debian like Linux systems and of Linux in general. Commands beginning with sudo are to be run on the host system while others are to be run as root inside the chroot.
- Partition the CF card and mount the target / filesystem at /mnt/target. I use one large root partion and add some swap. There is some concern that allocating swap on a CF card will cause significant write activity and shorten the lifespan of the card. I only run the ISC dhcpd, Bind, ntpd and a couple of shell sessions so I fit into my 256MB of RAM easily and the swap is just a saftey net. If you want something different, adjust accordingly.
sudo mkdir /mnt/target sudo cfdisk /dev/sdb # I put swap in sdb5 and the rest of the CF card into sdb1 sudo mke2fs -j /dev/sdb1 sudo mount /dev/sdb1 /mnt/target
- Mount the installation ISO. You can use any network mirror in the next step if you don’t want to download the ISO – see debootstrap(8) for more information.
sudo mkdir /mnt/iso sudo mount -t iso9660 -o ro,loop=/dev/loop0 /temple/sw/linux/ubuntu-7.04-server-i386.iso /mnt/iso
- Run debootstrap:
sudo apt-get install debootstrap sudo debootstrap --arch i386 feisty /mnt/target file:/mnt/iso
- Chroot into the target:
sudo chroot /mnt/target /bin/bash
- Make /etc/fstab:
# file system mount point type options dump pass
/dev/hda1 / ext3 defaults 0 0
/dev/hda5 none swap sw 0 0
tmpfs /tmp tmpfs size=128m,mode=1777 0 0
proc /proc proc defaults 0 0
sys /sys sysfs defaults 0 0
- Mount all filesystems and run mkswap:
mount /proc
mount /sys
ls /proc # verficiation. if the directory is empty, it isn't mounted.
mkswap /dev/hda5
- Configure keyboard. A keyboard isn’t required for a headless box so perhaps this step can be removed.
dpkg-reconfigure console-setup
- Setup networking:
editor /etc/network/interfaces
- set hostname:
echo pathos > /etc/hostname
- Setup a nonroot user:
adduser foo
echo 'foo ALL=(ALL) ALL' >> /etc/sudoers
chmod 0440 /etc/sudoers
- Setup /etc/apt/sources.list, /etc/hosts and /etc/resolv.conf. See here for a sample sources.list.
- Create the file /etc/event.d/ttyS0:
start on runlevel 2
start on runlevel 3
start on runlevel 4
start on runlevel 5
stop on runlevel 0
stop on runlevel 1
stop on runlevel 6
respawn
exec /sbin/getty -L ttyS0 9600 vt102
- Edit the file /etc/initramfs-tools/modules and add the following two lines at the end of the file:
ext3
ide_generic
Now, you have to update your initramfs with
update-initramfs -u
- Install a kernel and configure grub. debootstrap will not install a bootloader for you. See here for a sample menu.lst that should work for feisty. Make sure that you adjust it for the kernel version installed by linux-image-generic. You may wish to look at the menu.lst from a running, recent Debian or Ubuntu system and include the comment lines used to set default options via update-grub. Note the bits that enable the serial console and set the speed.
The -server kernel did not boot on my net4801.
apt-get install linux-image-generic grub memtest86+
mkdir -p /boot/grub
cp /usr/lib/grub/i386-pc/* /boot/grub
editor /boot/grub/menu.lst
exit # exit the chroot(), that is
# Run this from outside the chroot()
sudo grub-install --no-floppy --root-directory=/mnt/target /dev/sdb1
- Install the CF card in the Soekris and boot. At this point, you should have a working but very minimal Ubuntu system. You should be able to login via the serial console as user foo with the password that you fed to adduser and from there sudo to root.
- Do whatever you need to do to install your applications and configuration data. Personally, I use slack.
